Truck Heading to the Shop |
04-10-2017, (Subject: Truck Heading to the Shop ) Post: #2 | |||
| |||
RE: Truck Heading to the Shop TSB130099 Technical Service Bulletin Subject Engine Control Module (ECM) Calibration and Aftertreatment Selective Catalytic Reduction (SCR) Catalyst Compatibility Issue Engine control module (ECM) calibrations released after June 21, 2013 are only compatible with specific aftertreatment selective catalytic reduction (SCR) catalyst part numbers. Downloading newer versions of an ECM calibration may require the aftertreatment SCR catalyst to be replaced. To determine the appropriate repair direction, use the ISX12/15 CM2350 Calibration Selection Tool. See link provided below. Verification Product Affected ISX12 CM2350 X102 ISX15 CM2350 X101 Use the ISX12/15 CM2350 Calibration Selection Tool below to determine if a replacement SCR catalyst is required following an ECM calibration download or if an alternate ECM calibration is available to address the issue on the subject engine. An alternate ECM calibration that does not require an SCR catalyst replacement may be available. NOTE: https://quickserve.cummins.com/qs3/porta...index.html In addition, check the ECM calibration revisions history on QuickServe Online under My Applications section for the specified ECM base code. See link below. NOTE: https://quickserve.cummins.com/qs3/porta...ader=false Aftertreatment SCR catalyst compatibility with ECM Calibrations released after June 21, 2013 can be found in Table 1. Aftertreatment SCR catalysts that are compatible with ECM calibrations released after June 21, 2013 can also be visually identified by dimples in the aftertreatment SCR catalyst heat shield. These dimples go around the circumference of the aftertreatment SCR catalyst heat shield and can be found in three different locations equidistant around the circumference. See Figure 1. Figure 1, Aftertreatment SCR Catalyst Heat Shield Dimples Resolution Prior to performing any resolution which includes an ECM calibration and SCR catalyst part number update, troubleshoot any fault codes or symptoms included in the original complaint. Follow the verification steps outlined above to determine an appropriate ECM calibration and aftertreatment SCR catalyst dependent on the level of repair being performed. In addition, reference QuickServe Online under the Service tab for any applicable Temporary Repair Practices (TRP) or Campaigns for the subject engine. If the ISX12/15 CM2350 Calibration Selection Tool directs replacement of the aftertreatment SCR catalyst, the compatible part numbers are located in Table 1. Table 1, Aftertreatment SCR Catalyst Compatibility with ECM Calibration Revisions Released After June 21, 2013 Non-Compatible 5303895 5303897 5303893 5303865 5303910 5308328 5308330 5303914 5303912 5303917 4328765 5303811 5303813 4328754 4328755 4328756 4328757 4328758 4328767 5309391 5309557 5308460 5308401 5308405 5309247 5312174 5308417 5308439 5311483 5309396 5309546 5309552 5309903 5308703 5308705 5308707 5311261 5310478 5310482 5310298 5308450 5308452 5309243 5308360 5311785 5310179 5308395 5312382 5312171 5312342 5310474 4328775 Compatible 4328791 4328792 4328793 4328794 4328795 4328796 4328797 4328798 4328799 4328800 4328801 4328802 5313981 5313982 5313983 5313984 5313985 5313986 5313987 5313988 5313989 5313990 5313991 5313992 5313993 5313995 5313996 5313997 5313998 5313999 5314000 5314001 5314002 5314003 5314004 5314005 5314006 5314007 5314008 5314009 5314010 4328804 4328780 4328781 4328782 4328783 4328784 4328785 4328786 4328787 4328789 4328790 Stand-alone Part Numbers 5308751 4328788 5308454 5309911 5311328 5311330 4329551 4353331 4353333 4323335 4353337 4353339 4353341 4353343 4353345 Warranty Statement The information in this document has no effect on present warranty coverage or repair practices, nor does it authorize TRP or Campaign actions. Document History Date Details 2013-6-21 Module Created 2013-7-3 Added part number cross reference 2014-7-7 none 2014-10-6 Work Order 64494 2015-1-19 Added references to Calibration Selection Tool and updated Table 1. 2015-4-9 Updated language. Last Modified: 15-Apr-2015 | |||
|
« Next Oldest | Next Newest » |
Messages In This Thread |
Truck Heading to the Shop - lovoltage - 04-10-2017, RE: Truck Heading to the Shop - lovoltage - 04-10-2017 |
NOTE: Rawze.com is not affiliated, nor endorses any of the google ads that are displayed on this website.