Doing cams and front structure

Rawze.com: Rawze's ISX Technical Discussion and more

New: Rawze's amazon Page

A big THANK YOU For those who have recently Contributed towards keeping the lights on around here. It helps keep the website costs at bay and goes towards helping others with their trucks.

I want to personally thank everyone who has donated to the forum recently. It helps pay for the $790/month internet bill that the forum consumes. - Thank you again.

YOU NEED AN INVITATION CODE TO Register! -- To obtain an invitation code, please e-mail [email protected] with a reason why you want to join. This keeps the spammers out and our forum clean.

Current time: 11-26-2024, | ShoutboxHello There, Guest! (Login — Register)

Threaded Mode | Linear Mode

Doing cams and front structure

10-13-2016, (Subject: Doing cams and front structure )

Post: #26

Hammerhead Offline

Offline

Kookoo for Cocoa Puffs (1922 Likes)

Posts: 1,400
Joined: May 2016

Thanks: 1014
Given 1922 thank(s) in 741 post(s)

RE: Doing cams and front structure

(10-13-2016 )Brock Wrote: Well I'm finally back on the road. took too long... Went a little ape shi#t with the Cummins red paint!

Shimmer up the oil pump. bobtail right now 200f oil temp has me at 52psi oil pressure. once I'm hooked to a trailer I expect I'll be just below 50.

This truck hasnt ran this smooth since new. purrs like a kitten.

Heads up Brock, I was advised by a very well known member that oil pressure over 50psi has the potential to wash out the bearings in an ISX!
You might want to pull one dime out at your earliest opportunity!

Hopefully some of the gurus will chime in on this...

User's Signature: Why? Why do I always ask "why?" Because I can't learn or help teach others with "'cause I said so..."

Return to Top | find

« Next Oldest | Next Newest »

Messages In This Thread

Doing cams and front structure - Brock - 10-03-2016,

RE: Doing cams and front structure - Pigpen 2868 - 10-03-2016,

RE: Doing cams and front structure - Signature620 - 10-04-2016,

RE: Doing cams and front structure - hhow55 - 10-04-2016,

RE: Doing cams and front structure - Brock - 10-04-2016,

RE: Doing cams and front structure - Hammerhead - 10-04-2016,

RE: Doing cams and front structure - Brock - 10-04-2016,

RE: Doing cams and front structure - hhow55 - 10-04-2016,

RE: Doing cams and front structure - Texasdude74 - 10-05-2016,

RE: Doing cams and front structure - Rawze - 10-06-2016,

RE: Doing cams and front structure - Texasdude74 - 10-06-2016,

RE: Doing cams and front structure - Rawze - 10-05-2016,

RE: Doing cams and front structure - Brock - 10-05-2016,

RE: Doing cams and front structure - preacherboy24 - 10-06-2016,

RE: Doing cams and front structure - Brock - 10-06-2016,

RE: Doing cams and front structure - Hammerhead - 10-06-2016,

RE: Doing cams and front structure - Brock - 10-06-2016,

RE: Doing cams and front structure - Hammerhead - 10-06-2016,

RE: Doing cams and front structure - hhow55 - 10-06-2016,

RE: Doing cams and front structure - Brock - 10-07-2016,

RE: Doing cams and front structure - Hammerhead - 10-08-2016,

RE: Doing cams and front structure - Rawze - 10-08-2016,

RE: Doing cams and front structure - Brock - 10-08-2016,

RE: Doing cams and front structure - Brock - 10-13-2016,

RE: Doing cams and front structure - Hammerhead - 10-13-2016

RE: Doing cams and front structure - in2trux - 10-13-2016,

RE: Doing cams and front structure - RPM1 - 10-13-2016,

RE: Doing cams and front structure - RPM1 - 10-13-2016,

RE: Doing cams and front structure - Hammerhead - 10-14-2016,

RE: Doing cams and front structure - RPM1 - 10-14-2016,

RE: Doing cams and front structure - Brock - 10-14-2016,

RE: Doing cams and front structure - Running rough - 10-14-2016,

RE: Doing cams and front structure - Hammerhead - 10-14-2016,

RE: Doing cams and front structure - Running rough - 10-14-2016,

RE: Doing cams and front structure - Brock - 10-15-2016,

RE: Doing cams and front structure - Rawze - 10-16-2016,

RE: Doing cams and front structure - Brock - 10-16-2016,

RE: Doing cams and front structure - preacherboy24 - 10-17-2016,

RE: Doing cams and front structure - Brock - 10-17-2016,

RE: Doing cams and front structure - RPM1 - 10-17-2016,

RE: Doing cams and front structure - in2trux - 10-17-2016,

NOTE: Rawze.com is not affiliated, nor endorses any of the google ads that are displayed on this website.

Theme by MyBB Addict
Contact Us | Rawze.com | Return to Top | Return to Content | Lite (Archive) Mode | RSS Syndication

Powered By MyBB, © 2002-2024 MyBB Group | Theme by Laughing Inc - Web Design