Incomplete regen and turbo delay cm871

[Rawze]

(06-24-2021 )Big red 09 Wrote:  ...
: SPN 5018 Active
...

This is the cry-baby alarm for the CM871. It will throw this alarm whenever anything is wrong with the system. Could literally be anything causing it that it cannot detect... all it knows is that pressures are "estimated" to be too high.

NOTE: That I said "Estimated"... and not "Measured". that is important to know.

(06-24-2021 )Big red 09 Wrote:  ...
The doc was cleaned and the dpf was replaced
...

WHY was the DPF replaced and the DOC only cleaned and not replaced as well?.. What are their ages?.

You also mentioned the egr coolar was replaced. Was i leaky? .. If so then that DOC is ruined!.

(06-24-2021 )Big red 09 Wrote:  ...
along with egr cooler(which of course shouldn’t be issue for this symptom)
...

If the EGR cooler was leaky, you can kiss that DOC goodbye. ANY sort of liquid intrusion into the DOC and DPF elements will cause them to become significantly weakened. This is because there are trace amounts of precious metals i them and any liquids whatsoever causes them to oxidize and also to get washed away. This is also why someone cannot clean these elements with any sort of liquids too, like you see those complete morons do on the social medai and the Youtubes.


-- LAST but not LEAST... That is a cry-baby alarm. - There is an internal soot-counter inside that ecm... it "Estimates" the amount of soot in the DPF unit and it DOES NOT COUNT DOWNWARDS" EVEN IF THERE IS A REGEN CYCLE. - It Assumes over time how blocked up that DPF unit is and eventually starts causing that error your having. - The only way to reset this counter is to remove the DOC and DPF ... take them somewhere and have them baked, de-ashed, flow tested to ensure they pass. After that, they get re-installed and ...

ONLY WHEN A PASSING SET OF doc/dpf ELEMENTS IS FIRST INSTALLED: -- Then to perform in Insite software, the "Maintenance Reset" and "New DPF Filter" install procedures for the ecm to reset these counters. - if this is not performed, then that ecm is going to do noting but complain about those new elements and continue to complain they are clogged up all the time. - SOME of the Styealers#its and repair shops do not perform this step and then you end up spending thousands#$$$$ on chasing ghosts and it runs you out of business, either because they are severely under-trained ... or they do it on purpose to try to run your bill, sell you new turbo's and all sorts of expensive parts.

- Welcome to modern trucking... GET AWAY FROM THOSE REPAIR SHOPS... ESPECIALLY THE OEM-CERTIFIED PLACES... THEY WILL BANKRUPT YOU, LEAVE YOU WITH HALF-ARSSED REPAIRS, AND RUN YOUR BUSINESS INTO THE GROUND IN A HURRY!... AND EVERYTHING THEY DO.. YOU WILL HAVE TO RE-DO AGAIN BECAUSE OF LAZY, SPEED-GUN HAPPY IDIOTS!.

=============

- On average, a well cared for CM871 with regular tune-up work and the emissions system looked after properly ... the DOC and DPf will last about 600k miles or so before getting worn to the point of replacement.


- Also, whenever a DOC/DPF gets replaced on a CM871, there has been some updates for them, along with newer part#s . There is specific programming changes required to go along with this too, or it will not function properly and it will give troubles.
here is a related post that talks about this...
http://rawze.com/forums/showthread.php?t...7#pid45177

LASTLY:... If it is complaining about being face-plugged again already ... THEN TAKE IT OFF AND TAKE PICS OF ITS FACES!... AND POST THE PHOTOS HERE FOR OPINIONS!... STOP GUESSING AT IT AND START TAKING THINGS APART AGAIN!. This gives you the opportunity to take them to have baked, flow-tested, etc. to see if they pass (by a different shop hopefully), and to do that reset in insite when they are verified to have passed. - START working on that thing yourself, because no one else is going to do a proper job of it... They are not trained to do so .. and they could care less!.