Excess blowby
06-18-2016, (Subject: Excess blowby ) 
Post: #35
RE: Excess blowby
(06-17-2016 )Unilevers Wrote:  
(06-17-2016 )ynot Wrote:  are you talking 1000+ on the outside of the manifold?? cause I've got a prob inside the manifold and I'm topping out at 1150 with no issues what so ever, I keep reading about 1250 being melt down for aluminum pistons and the isx's use monotherm pistons, so you should have been fine I would think. man she must have gotten some hot in there for that too happen.

lol i ran one at 1650 pre turbo temp on a dyno - it was terrifying but it held....
Ok so since I have my shiny new pyro and I'm going to install it when I get home...I have a few other repairs to do at the same time, which position is best to place the probe, pre-turbo or post-turbo and why?
I'm going to have the coolant drained anyhow, and I'm planning on doing a turbo inspection (likely replacement) anyhow, turbo removal to drill & tap the manifold isn't a big issue so that removes the ease of drilling and tapping downstream of the turbo as the obvious reason. What I'm looking for, is there a reason pro or con upstream or downstream that I don't know to ask?
replyreply


Messages In This Thread
Excess blowby - in2trux - 05-17-2016,
RE: Excess blowby - Nilao - 05-17-2016,
RE: Excess blowby - in2trux - 05-17-2016,
RE: Excess blowby - in2trux - 05-17-2016,
RE: Excess blowby - mkmac - 05-17-2016,
RE: Excess blowby - Nilao - 05-17-2016,
RE: Excess blowby - hhow55 - 05-17-2016,
RE: Excess blowby - in2trux - 05-17-2016,
RE: Excess blowby - Nilao - 05-17-2016,
RE: Excess blowby - in2trux - 05-17-2016,
RE: Excess blowby - in2trux - 05-19-2016,
RE: Excess blowby - hhow55 - 05-22-2016,
RE: Excess blowby - in2trux - 05-17-2016,
RE: Excess blowby - hhow55 - 05-17-2016,
RE: Excess blowby - in2trux - 05-22-2016,
RE: Excess blowby - hhow55 - 05-22-2016,
RE: Excess blowby - in2trux - 05-28-2016,
RE: Excess blowby - Vin - 05-28-2016,
RE: Excess blowby - in2trux - 05-28-2016,
RE: Excess blowby - bazdan902 - 05-29-2016,
RE: Excess blowby - Marajin - 05-29-2016,
RE: Excess blowby - Waterloo - 05-29-2016,
RE: Excess blowby - bazdan902 - 05-29-2016,
RE: Excess blowby - bazdan902 - 05-29-2016,
RE: Excess blowby - in2trux - 05-29-2016,
RE: Excess blowby - in2trux - 06-16-2016,
RE: Excess blowby - T680 - 06-17-2016,
RE: Excess blowby - in2trux - 06-17-2016,
RE: Excess blowby - ynot - 06-17-2016,
RE: Excess blowby - Unilevers - 06-17-2016,
RE: Excess blowby - Hammerhead - 06-18-2016
RE: Excess blowby - gearhead - 06-19-2016,
RE: Excess blowby - Rawze - 06-19-2016,
RE: Excess blowby - Hammerhead - 06-20-2016,
RE: Excess blowby - Rawze - 06-20-2016,
RE: Excess blowby - Wiseman - 06-20-2016,
RE: Excess blowby - Hammerhead - 06-20-2016,
RE: Excess blowby - Bmyetrkg24 - 07-01-2016,



NOTE: Rawze.com is not affiliated, nor endorses any of the google ads that are displayed on this website.