+- Rawze.com: Rawze's ISX Technical Discussion and more (http://rawze.com/forums)
+-- Forum: Big Truck Technical Discussion... (/forumdisplay.php?fid=1)
+--- Forum: Ask Your question... (/forumdisplay.php?fid=45)
+--- Thread: Changing clutch brakes. (/showthread.php?tid=1539)
Changing clutch brakes. - indian_richard - 03-05-2017
Does anybody know of another way to change clutch brakes without removing the transmission? I used the oxygen acetylene torch so you can imagine how pleasant that was. Lol
I couldn't use the air chisel on this one because the little knubs that keep it from spinning were sheared off.
I hope there is an easier way of doing this. Lol
RE: Changing clutch brakes. - Hammerhead - 03-05-2017
(03-05-2017 )indian_richard Wrote: Does anybody know of another way to change clutch brakes without removing the transmission? I used the oxygen acetylene torch so you can imagine how pleasant that was. Lol
I couldn't use the air chisel on this one because the little knubs that keep it from spinning were sheared off.
I hope there is an easier way of doing this. Lol
-Air hammer with a chisel tool
-Reciprocating saw
-Roto tool. Think dentist drill, that the rotating tool is driven via a long umbilical with the motor a good two feet away. Not a common tool, I got it to port heads and use it occaisionally for oddball jobs such as this. Kinda like a dremel.
-Cutting torch and good leather protective gear so you don't get burned
This is the order of preference for me, I will never again install a clutch brake that is not a "two piece" to facilitate simpler replacement while the clutch & tranny are in place.
RE: Changing clutch brakes. - indian_richard - 03-05-2017
(03-05-2017 )Hammerhead Wrote:Those are a few good alternatives. I have another clutch brake I need to change, so now I have a few more options before I get out the torch. Thnx(03-05-2017 )indian_richard Wrote: Does anybody know of another way to change clutch brakes without removing the transmission? I used the oxygen acetylene torch so you can imagine how pleasant that was. Lol
I couldn't use the air chisel on this one because the little knubs that keep it from spinning were sheared off.
I hope there is an easier way of doing this. Lol
-Air hammer with a chisel tool
-Reciprocating saw
-Roto tool. Think dentist drill, that the rotating tool is driven via a long umbilical with the motor a good two feet away. Not a common tool, I got it to port heads and use it occaisionally for oddball jobs such as this. Kinda like a dremel.
-Cutting torch and good leather protective gear so you don't get burned
This is the order of preference for me, I will never again install a clutch brake that is not a "two piece" to facilitate simpler replacement while the clutch & tranny are in place.
Yeah I replaced this clutch brake with a Babcock two piece. Hopefully I won't have to replace it. Lol
RE: Changing clutch brakes. - joed2323 - 03-05-2017
I've used torch, only suggest it if your the type that says "f" it and geterdone.
Otherwise do it the chisel way
I've had the tabs bust off before. If you can wedge something up in their to get it to quit spinning it helps. Otherwise once you start chiselling the crap out of it it will quit spinning as easy.
I also suggest getting atleast 3-4 chisels sharpened at once so you don't have to get out from under the truck so many times to resharpen the chisels...
RE: Changing clutch brakes. - un_yun - 03-06-2017
I always used an air chisel. I always make sure I get a two piece brake, every time I need one
RE: Changing clutch brakes. - Emeryville64 - 03-06-2017
Just don't forget to grease your clutch brake. If you don't believe me check with Eaton.
RE: Changing clutch brakes. - gatow900 - 03-06-2017
RE: Changing clutch brakes. - gatow900 - 03-06-2017
Cut a 1/5 of the disc and force it in front of the bad clutch brake