Coolant leak
10-19-2019, (Subject: Coolant leak ) 
Post: #10
RE: Coolant leak
Well Thx Rawze for reminding me I don't want to be dependent on these crooked shops! I got out there this morning in the rain and found 2 water leaks! I've still got to get a new clamp and gasket for rear of egr cooler that is not sealing back up but for right now coolant pressure is holding! I'm gonna replace imap and delpta p sensor also today, my 2350 is different than cummins your video showed egr lineup on, so any advice on what else I should do to egr system? Thx
replyreply
10-19-2019, (Subject: Coolant leak ) 
Post: #11
RE: Coolant leak
Tune up, not line up
replyreply
10-19-2019, (Subject: Coolant leak ) 
Post: #12
RE: Coolant leak
(10-19-2019 )tree98 Wrote:  Ask and you shall receive https://youtu.be/tNmQnAJzmVo
Thx
replyreply
10-19-2019, (Subject: Coolant leak ) 
Post: #13
RE: Coolant leak
You also need to go to quickserve.com and register your engine serial number(you'll find it on the valve cover..ESN) its FREE.

https://quickserve.cummins.com/info/index.html

Once you do that you can look up parts and service procedures for your exact engine. Although Rawze's method for testing an EGR cooler is better than the method Cummins wants you to use. Your engine is a little different than the one in that video but the principal is the same.
replyreply
 Thanks given by: Bama Boy
10-19-2019, (Subject: Coolant leak ) 
Post: #14
RE: Coolant leak
(10-19-2019 )tree98 Wrote:  You also need to go to quickserve.com and register your engine serial number(you'll find it on the valve cover..ESN) its FREE. Once you do that you can look up parts and service procedures for your exact engine. Although Rawze's method for testing an EGR cooler is better than the method Cummins wants you to use. Your engine is a little different than the one in that video but the principal is the same.

Thx I will definitely do that!
replyreply
10-19-2019, (Subject: Coolant leak ) 
Post: #15
RE: Coolant leak
Ok I know have a new clamp and gasket for back of egr cooler, is there anything special about this gasket when putting back together?
replyreply
10-19-2019, (Subject: Coolant leak ) 
Post: #16
RE: Coolant leak
Seems like success, new clamp and gasket on EGR cooler worked aloft better with new parts! Replaced both upper radiator hoses and pumped back up to 20psi waiting to see if it holds now.
replyreply
 Thanks given by: Rawze , tree98
10-20-2019, (Subject: Coolant leak ) 
Post: #17
RE: Coolant leak
What are you using to pressurize the coolant system? And that is needed to connect to a T680? I’m looking to test my system
replyreply
10-20-2019, (Subject: Coolant leak ) 
Post: #18
RE: Coolant leak
(10-20-2019 )Zondo956 Wrote:  What are you using to pressurize the coolant system? And that is needed to connect to a T680? I’m looking to test my system

I use this kit...
https://amzn.to/35PdSEA

A lot of stuff mentioned on this forum can be found on my amazon page...
https://www.amazon.com/shop/rawzescollection


User's Signature: ->: What I post is just my own thoughts and Opinions! --- I AM Full Of S__T!.
replyreply




NOTE: Rawze.com is not affiliated, nor endorses any of the google ads that are displayed on this website.