ISX and Bypass Oil Filter Systems
08-01-2016, (Subject: ISX and Bypass Oil Filter Systems ) 
Post: #55
RE: ISX and Bypass Oil Filter Systems
i have the same kit, if i remember it's a AN6 fitting that will work. or jic(same thing) fittings that came with it. just take 1 of the fittings to a hose or farm(ih case JD) dealer they should have what you need.just read through the post its in here somewhere.Smile
replyreply
 Thanks given by: LargeCar
08-01-2016, (Subject: ISX and Bypass Oil Filter Systems ) 
Post: #56
RE: ISX and Bypass Oil Filter Systems
Not the jic size, the other end that threads into the base. I'm looking to order it online. I don't have the kit yet. I think it might be 3/8?
replyreply
08-01-2016, (Subject: ISX and Bypass Oil Filter Systems ) 
Post: #57
RE: ISX and Bypass Oil Filter Systems
Nevermind found it. It's 3/8 x 1/2 jic
replyreply
08-10-2016, (Subject: ISX and Bypass Oil Filter Systems ) 
Post: #58
RE: ISX and Bypass Oil Filter Systems
Hey guys can anyone please tell me which fitting I need for supply line from oil cooler housing labeled number 5 (back in this post) and which fitting I need for return line to side of the oil pan (cm871). I have already ordered the amsoil bypass kit. Thanks in advance.
replyreply
08-11-2016, (Subject: ISX and Bypass Oil Filter Systems ) 
Post: #59
RE: ISX and Bypass Oil Filter Systems
(08-10-2016 )Inderjit Wrote:  Hey guys can anyone please tell me which fitting I need for supply line from oil cooler housing labeled number 5 (back in this post) and which fitting I need for return line to side of the oil pan (cm871). I have already ordered the amsoil bypass kit. Thanks in advance.

9068-08-18 9068-08-18 | 1/2" JIC Male x M18x1.5 Metric Male w/ seal
$6.24
$5.87

9068-08-14 9068-08-14 | 1/2" JIC Male x M14x1.5 Metric Male w/ seal
$7.05
$6.63

http://www.discounthydraulichose.com/906...p/9068.htm

This is a link to order the fittings online. Cuz fitting may be hard to find in some stores
replyreply
 Thanks given by: fargonaz , LargeCar
08-11-2016, (Subject: ISX and Bypass Oil Filter Systems ) 
Post: #60
RE: ISX and Bypass Oil Filter Systems
(08-11-2016 )jimeneztrans84 Wrote:  
(08-10-2016 )Inderjit Wrote:  Hey guys can anyone please tell me which fitting I need for supply line from oil cooler housing labeled number 5 (back in this post) and which fitting I need for return line to side of the oil pan (cm871). I have already ordered the amsoil bypass kit. Thanks in advance.

9068-08-18 9068-08-18 | 1/2" JIC Male x M18x1.5 Metric Male w/ seal
$6.24
$5.87

9068-08-14 9068-08-14 | 1/2" JIC Male x M14x1.5 Metric Male w/ seal
$7.05
$6.63

http://www.discounthydraulichose.com/906...p/9068.htm

This is a link to order the fittings online. Cuz fitting may be hard to find in some stores

Thanks so much for part numbers. Little more help if you have part number for 90 deg elbow fittings for amsoil filter housing. Thanks again.
replyreply
08-11-2016, (Subject: ISX and Bypass Oil Filter Systems ) 
Post: #61
RE: ISX and Bypass Oil Filter Systems
2501-08-06 | 1/2" JIC Male x 3/8" NPTF Male Pipe 90°

On the fittings for the engine feed and return make sure you leave the o ring only, take off the washer it comes with.
replyreply
 Thanks given by: LargeCar
08-14-2016, (Subject: ISX and Bypass Oil Filter Systems ) 
Post: #62
RE: ISX and Bypass Oil Filter Systems
Thank you sir
replyreply
08-17-2016, (Subject: ISX and Bypass Oil Filter Systems ) 
Post: #63
RE: ISX and Bypass Oil Filter Systems
(04-03-2016 )Rawze Wrote:  
(04-03-2016 )Waterloo Wrote:  For the bypass oil filter, where did you guys put the return line? Back to the oil pan I am assuming? Now, did you drill a hole in the pan or use the drain plug on the passenger side of the motor? Or is there someplace else to attach the oil return line? My motor is in a thousand pieces right now, and I am thinking this would be a good time to install a by pass filter, or at least get the plumbing started.

There are return ports down both sides of the engine just above the oil pan with large hex plugs in them. Just pick one that is convenient.

====================


I have the cheap Amsoil kit.

It is a BMK30 kit. Here is the link...
http://www.amsoil.com/shop/by-product/fi...e=BMK30-EA


The replacement filter is an eaBP-120. They are like $50.00, or $36.00 if you sign up as a dealer.


I also have the oil sampling valve. It screws ritght into the bypass filter kit, and makes it VERY easy to take oil samples. Here is the link...

https://www.amsoil.com/shop/by-product/f...?code=BK30


For Oil sampling, I use these sample kits,... they are pre-paid...

http://www.amsoil.com/shop/by-product/ot...e=KIT14-EA


Here is a pic of mine. It is mounted on the passenger side right behind my fuel tank with a aluminum plate and some "J" bolts from home depot. No holes were drilled into the frame at all. The filter lasts about 60 - 80k miles at a time.
Hey Rawze can I get part number the for the fitting at the inlet port of filter housing? Not the elbow but the other with a bend on it.
replyreply
 Thanks given by: Texmike





  
  
Theme by MyBB Addict
Contact Us | Rawze.com | Return to Top | Return to Content | Lite (Archive) Mode | RSS Syndication